目标

  了解如何查看服务器网络信息

操作演示

命令：ip

语法：ip 选项　参数
-c 带有颜色的输出
link 输出所有线路的
address 输出所有的IP地址

[root@sinfotek ~]# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp8s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
    link/ether 00:23:ae:88:0c:d2 brd ff:ff:ff:ff:ff:ff
3: virbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default qlen 1000
    link/ether 52:54:00:9e:82:36 brd ff:ff:ff:ff:ff:ff
4: virbr0-nic: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast master virbr0 state DOWN mode DEFAULT group default qlen 1000
    link/ether 52:54:00:9e:82:36 brd ff:ff:ff:ff:ff:ff
##查看所有线路的信息


[root@sinfotek ~]# ip -c -h address
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: enp8s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 00:23:ae:88:0c:d2 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.116/24 brd 192.168.1.255 scope global noprefixroute dynamic enp8s0
       valid_lft 76983sec preferred_lft 76983sec
    inet6 fe80::e2ec:52d8:20b4:8c6d/64 scope link noprefixroute 
       valid_lft forever preferred_lft forever
3: virbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000
    link/ether 52:54:00:9e:82:36 brd ff:ff:ff:ff:ff:ff
    inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0
       valid_lft forever preferred_lft forever
4: virbr0-nic: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast master virbr0 state DOWN group default qlen 1000
    link/ether 52:54:00:9e:82:36 brd ff:ff:ff:ff:ff:ff

##查看所有IP地址

[root@sinfotek ~]# ip -c -h route
default via 192.168.1.1 dev enp8s0 proto dhcp metric 100 
192.168.1.0/24 dev enp8s0 proto kernel scope link src 192.168.1.116 metric 100 
192.168.122.0/24 dev virbr0 proto kernel scope link src 192.168.122.1 
##查询路由表信息

命令实例

ip link show                     # 显示网络接口信息
ip link set eth0 up             # 开启网卡
ip link set eth0 down            # 关闭网卡
ip link set eth0 promisc on      # 开启网卡的混合模式
ip link set eth0 promisc offi    # 关闭网卡的混个模式
ip link set eth0 txqueuelen 1200 # 设置网卡队列长度
ip link set eth0 mtu 1400        # 设置网卡最大传输单元
ip addr show     # 显示网卡IP信息
ip addr add 192.168.0.1/24 dev eth0 # 设置eth0网卡IP地址192.168.0.1
ip addr del 192.168.0.1/24 dev eth0 # 删除eth0网卡IP地址

ip route show # 显示系统路由
ip route add default via 192.168.1.254   # 设置系统默认路由
ip route list                 # 查看路由信息
ip route add 192.168.4.0/24  via  192.168.0.254 dev eth0 # 设置192.168.4.0网段的网关为192.168.0.254,数据走eth0接口
ip route add default via  192.168.0.254  dev eth0        # 设置默认网关为192.168.0.254
ip route del 192.168.4.0/24   # 删除192.168.4.0网段的网关
ip route del default          # 删除默认路由
ip route delete 192.168.1.0/24 dev eth0 # 删除路由